环球效准仪使用方法：首先把适合要效的狗的插入管找到，(例如4.5mm内径的)，装入狗管固定。

然后再把黑色的校准镜筒装在插入管上固定好。接下来就可以校瞄了。接下来用肉眼通过光瞄去观察校正。

警告：一定THATTHE狗未加载，该行动是开放的，炮口指出在一个安全的DIRECTION.SAFE狗处理程序必须使用在任何时候。 
1.SCOPE安装 
 随着戒指已经安装到狗管， sepate上层部分的环除去的screws.Place范围上的底半的ring.Replace顶端松散不tighten.Rotate的范围立场上海拔turrst顶部的范围（垂直） 。看一个物体通过的范围，调整眼救济滑动它来回，直到正确的眼睛救济距离achieved.Tighten的紧定螺钉的顶端halver的戒指。 

2.ATTACHING的BORESIGHTER狗管口。 
 选择approprlate膛安娜堡从工具箱中选择口径表明相邻乔木和插入缺口年底到boresighter.Hand收紧锁定螺钉重视坚决boresighter （图1与2 ） 

警告：如果不承担螺柱实干家easly插入，删除，并确认正确的口径螺柱正被使用。 

插入另一端的螺柱到狗管口（图3 ） 

3.PRE ，零与BORESIGHTER 
 如果有必要，旋转boresighter ，直到网格线匹配纵向和横向的光环载体。删除偏差和海拔上限（如有必要） 。调整偏差和海拔塔楼，直到十字线与中心boresighter的Grid.Each司发车等于4M.OAor英寸至100码。预归零的范围现在是complete.Remove和承担的boresighter从每桶螺柱和安全中的供应情况。 


警告：一定THATTHE膛螺柱已删除BARREL.FAILURE这样做可能受损死刑狗手或旁观者。 

在核准的范围内的其他安全区，完成归零程序指出您的范围和狗支说明书。 

注意：眼睛和耳朵的保护，强烈建议。安全郡处理程序必须使用在任何时候。 

追求Boresighter目的是为您节省时间和金钱，让你预先零的scope.Final步骤归零应该在range.This套件涵盖了大多数人口口径的市场，使您可以使用它来零不同步狗，手狗，猎狗，和muzzleloaders 。

 

WARNING:BE CERTAIN THATTHE GUN IS NOT LOADED,THE ACTION IS OPEN ,AND THE MUZZLE IS POINTED IN A SAFE DIRECTION.SAFE GUN HANDLING PROCEDURES MUST BE USED AT ALL TIMES.

1.SCOPE MOUNTING

 With the rings already installed onto the firearm,sepate the upper section of the rings by removing the screws.Place the scope onto the the bottom halves of the ring.Replace the top loosely do not tighten.Rotate the scope to position the elevation turrst on top of the scope (vertical).Look at an object through the scope,adjust the eye relief by sliding it back and forth until the correct eye relief distance is achieved.Tighten the set screws on top halver of the rings.

 

2.ATTACHING THE BORESIGHTER TO FIREARM MUZZLE.

 Select the approprlate bore arbor from the kit by selecting caliber indicated next to each arbor and insert the notched end into the boresighter.Hand tighten the locking screw to attach firmly the boresighter (图1与2)

 

CAUTION：If the bore stud doer not insert easly,remove and verify that the correct caliber of stud is being used.

 

Insert the other end of the stud into the muzzle(图3)

 

3.PRE-ZEROING WITH THE BORESIGHTER

 If necessary,rotate the boresighter until the grid lines match vertically and horizontally with the reticle vectors. Remove the windage and elevation caps (if necessary).Adjust the windage and elevation turrets until the crosshairs line up with the center of the boresighter’s Grid.Each division on the grid is equal to 4M.O.A.or inches at 100 yards. Pre-zeroing the scope is now complete.Remove the boresighter and bore stud from the barrel and secure it in the supplied case.

 

 

WARNING:BE CERTAIN THATTHE BORE STUD HAS BEEN REMOVED FROM BARREL.FAILURE TO DO SO MAY RESULT IN INJURY OF DEATH TO THE SHOOTER OR BYSTANDERS.

 

At an approved range of other safe area,complete the zeroing procedures indicated in your scope and firearm instruction manual.

 

CAUTION:Eye and ear protection is strongly recommended. Safe gun handling procedures must be used at all times.

 

The Pursuit Boresighter is designed to save you time and money by allowing you to pre-zero the scope.Final steps in zeroing should be done at the range.This kit covers the most popula calibers in the market so you can use it to zero different rifles,pistols,shotguns,and muzzleloaders.

商品名称	ZOS 校准仪,校瞄仪,适合多种口径